NMEA 2000, abbreviated to NMEA2k or N2K and standardized as IEC 61162-3, is a plug-and-play communications standard used for connecting marine sensors and display units within ships and boats. Communication runs at 250 kilobits-per-second and allows any sensor to talk to any display unit or other device compatible with NMEA 2000 protocols.
Details
Electrically, NMEA 2000 is compatible with the Controller Area Network ("CAN Bus") used on road vehicles and fuel engines. The higher-level protocol format is based on SAE J1939, with specific messages for the marine environment. Raymarine SeaTalk 2, Raymarine SeaTalkNG, Simrad Simnet, and Furuno CAN are rebranded implementations of NMEA 2000, though may use physical connectors different from the standardised DeviceNet 5-pin A-coded M12 screw connector, all of which are electrically compatible and can be directly connected.
The protocol is used to create a network of electronic devices—chiefly marine instruments—on a boat. Various instruments that meet the NMEA 2000 standard are connected to one central cable, known as a backbone. The backbone powers each instrument and relays data among all of the instruments on the network. This allows one display unit to show many different types of information. It also allows the instruments to work together, since they share data. NMEA 2000 is meant to be "plug and play" to allow devices made by different manufacturers to communicate with each other.
Examples of marine electronics devices to include in a network are GPS receivers, auto pilots, wind instruments, depth sounders, navigation instruments, engine instruments, and nautical chart plotters. The interconnectivity among instruments in the network allows, for example, the GPS receiver to correct the course that the autopilot is steering.
History
The NMEA 2000 standard was defined by, and is controlled by, the US-based National Marine Electronics Association (NMEA). Although the NMEA divulges some information regarding the standard, it claims copyright over the standard and thus its full contents are not publicly available. For example, the NMEA publicizes which messages exist and which fields they contain, but they do not disclose how to interpret the values contained in those fields. However, enthusiasts are slowly making progress in discovering these PGN definitions.
Functionality
NMEA 2000 connects devices using Controller Area Network (CAN) technology originally developed for the auto industry. NMEA 2000 is based on the SAE J1939 high-level protocol, but defines its own messages. NMEA 2000 devices and J1939 devices can be made to co-exist on the same physical network.
NMEA 2000 (IEC 61162-3) can be considered a successor to the NMEA 0183 (IEC 61162-1) serial data bus standard. It has a significantly higher data rate (250k bits/second vs. 4800 bits/second for NMEA 0183). It uses a compact binary message format as opposed to the ASCII serial communications protocol used by NMEA 0183. Another improvement is that NMEA 2000 supports a disciplined multiple-talker, multiple-listener data network whereas NMEA 0183 requires a single-talker, multiple-listener (simplex) serial communications protocol.
Network construction
The NMEA 2000 network, like the SAE J1939 network on which it is based, is organized around a bus topology, and requires a single 120Ω termination resistor at each end of the bus. (The resistors are in parallel, so a properly terminated bus should have a total resistance of 60Ω). The maximum distance for any device from the bus is six metres. The maximum backbone cable length is 250 meters (820 feet) with Mini cable backbone or 100 meters (328 feet) with Micro cable backbone
Cabling and interconnect
The only cabling standard approved by the NMEA for use with NMEA 2000 networks is the DeviceNet cabling standard, which is controlled by the Open DeviceNet Vendors Association. Such cabling systems are permitted to be labeled "NMEA 2000 Approved". The DeviceNet standard defines levels of shielding, conductor size, weather resistance, and flexibility which are not necessarily met by other cabling solutions marketed as "NMEA 2000" compatible.
There are two sizes of cabling defined by the DeviceNet/NMEA 2000 standard. The larger of the two sizes is denoted as "Mini" (or alternatively, "Thick") cable, and is rated to carry up to 8 Amperes of power supply current. The smaller of the two sizes is denoted as "Micro" (or alternatively, "Thin") cable using the M12 5-pin barrel connector specified in IEC 61076-2-101, and is rated to carry up to 3 Amperes of power supply current.