The Spoornet Class 18E, Series 1 of 2000 is a South African electric locomotive.

Beginning in 2000, Spoornet embarked on a program to rebuild Class 6E1 locomotives to Class 18E, Series 1 locomotives. Most of the Class 6E1s which had previously been reclassified or modified to Class 16E or Class 17E respectively were rebuilt to Class 18E as well.

South African Class 18E, Series 1

Manufacturer

The 3 kV DC Class 6E1 electric locomotive was built for the South African Railways (SAR) by Union Carriage & Wagon (UCW) in Nigel, Transvaal, with the electrical equipment supplied by the General Electric Company (GEC). Eleven series of Class 6E1 were delivered between 1969 and 1984, with altogether 960 units built. UCW did not allocate builder's numbers to the locomotives which it built for the SAR, but used the SAR unit numbers for their record keeping.

South African Class 18E, Series 1

Rebuilding

The rebuilding to Class 18E, Series 1 was done by Transwerk, later renamed Transnet Rail Engineering (TRE) and then Transnet Engineering (TE), at its Koedoespoort workshops in Pretoria. The rebuilding to Series 1 locomotives ceased in 2009, with 446 units rebuilt from Class 6E1, Series 6 to 11 locomotives, numbered in the ranges from to and to .

South African Class 18E, Series 1

Since it was probably not intended at the beginning of the project to rebuild virtually the whole fleet of Class 6E1s to Class 18Es, most of the early rebuilds were done on the newest of the Class 6E1 fleet, Series 8 to 11. One of the reasons was that these series, numbers E1896 and up, already had an air equipment frame brake system, commonly referred to as a brake rack, similar to that intended for the Class 18E which would reduce the overall per-unit cost of rebuilding.

Another consideration was possibly that their bodywork usually required less heavy repairs than the older models in terms of rust and other damage, such as bent panels and frames.

Similar considerations possibly also applied when older Class 6E1s of Series 6 and 7 began to be rebuilt in 2003, since these units in the number range from E1646 to E1895, used the same brake valve as that of the Class 18E. The result by 2013, however, was a fleet of already ageing Class 18Es and ancient Class 6E1s, the latter mostly of Series 6 and older models.

Orientation

The Class 6E1 was a dual cab locomotive and had a roof access ladder on one side only, just to the right of the cab access door. The roof access ladder end was marked as the no. 2 end. A corridor along the centre of the locomotive connected the cabs, which are identical apart from the fact that the handbrake is located in cab 2.

The rebuilt Class 18E locomotive, on the other hand, is a single cab unit since cab 1 was stripped of all controls during the rebuilding to have additional equipment and a chemical toilet installed. Since the driving cab's noise level had to be below 85 decibels, cab 2 was selected as the Class 18E driving cab, primarily based on its lower noise level compared to cab 1, which is closer and more exposed to the compressor's noise and vibration. Another factor was the closer proximity of cab 2 to the low voltage switch panel. The fact that the handbrake was located in cab 2 was not a deciding factor, but was considered an additional benefit.

On some early rebuilds a small plate, about the size of a cigarette packet and engraved with the upgrade information was attached on the cab wall in Cab 1 next to the compressor ventilation opening. The specimen depicted is in error about the original Class 6E series, which was S11 in the case of no. E2167.

Brake systems

Air brakes

The Class 6E1 locomotives were built with an air brake system, consisting of various valves connected to each other with pipes, commonly referred to as a “bicycle frame” brake system. The compressed air pipe is run through bolster and other members and then in a zig-zag pattern under the locomotive's belly to extend its length, which allows the maximum amount of moisture to condense on the way to the reservoirs. As a result, it has multiple pipe connections. A weakness of the system was that, after an accident or even a hard coupling, these pipes tended to develop leaks at the joints which were extremely difficult to repair.