A V4 engine is a four-cylinder piston engine where the cylinders share a common crankshaft and are arranged in a V configuration.
The V4 engine is less common compared to straight-four engines. However, V4 engines have been used in automobiles, motorcycles, and other applications.
Design
Some V4 engines have two crankpins that are shared by opposing cylinders. The crankshaft is usually supported by three main bearings in this type of engines. However this arrangement results an uneven firing engine. Split crankpins are preferred for even firing intervals.
Compared to the more common inline-four engine layout, a V4 engine is much shorter. Although different V angles can be used, if the two pistons are at a 90° V-angle with shared crankpins, the engine offers the additional advantage of perfect primary balance that reduces vibration. The design can also result in a smaller rocking couple than an inline-four engine, and the shorter crankshaft is less susceptible to the effects of torsional vibration due to its increased stiffness.
Disadvantages of V4 engines include its design being inherently wider compared to inline-4 engines, as well as the requirement of two exhaust manifolds, two-cylinder heads, and two valvetrains (thus needing two or four camshafts for overhead cam engines) rather than only one cylinder head, one manifold, one valvetrain, and one or two camshafts for an inline-four engine. Having two separate banks of components increases cost and complexity in comparison with inline four engines.
Because V4 engines are wider than inline-four engines, incorporating auxiliary drives, inlet systems, and exhaust systems while maintaining an overall compact size may be more difficult like other V-type engines. In order to reduce width, a narrower V-angle could be utilized, such as 60 degrees. Although a 60° V4 is more compact than a 90° V4 engine, the 60° design does not have perfect primary balance (if the crankpins are not split) and, therefore, often require a balance shaft to reduce vibrations similar to the V6 engines. Additionally, any (four-stroke) V4 engine with shared crankpins will fire unevenly and potentially require a heavier flywheel. Using split crankpins in a 60° V4, as used on the Ford Essex V4 engine and Ford Taunus V4 engines, results in an even firing order.
Automobile use
The earliest automotive use of V4 engines were in Grand Prix racing (later called 'Formula One') cars. One of the pioneering V4 engines was in the 1898 Mors rear-engined car built in France. At the time, the lack of vibration from the V4 engine was a key selling point. However, the car's V4 engine was replaced by a conventional inline-four engine by 1901.
In the 1907 French Grand Prix, the car entered by J. Walter Christie used a V4 engine, the largest engine ever used in a Grand Prix race. The engine was mounted transversely in the front and the car was front-wheel drive. The car retired from the French Grand Prix after just four laps, however, it later set a speed record of .
The first V4 engine used in production cars was the Lancia V4 engine that was first used in the 1922 Lancia Lambda. The Lancia engine was a narrow-angle design with an angle of 20 degrees between the banks and a single cylinder head with one overhead camshaft shared by both banks. It also used aluminium for both the block and head (which was unusual for the time). Lancia produced V4 engines until 1976, when they were replaced by flat-four engines.
The 1960-1994 ZAZ Zaporozhets is a Soviet city-type car that used a rear-mounted V4 engine. This engine was based on the design used in the LuAZ-967 amphibious military vehicle. It featured air-cooling with a magnesium block and was produced in displacements from .
The AMC Air-cooled 108 was a engine built from 1960 to 1963 for use in the lightweight M422 Mighty Mite military vehicle. The M422 developed was by American Motors Corporation (AMC) in the United States and specifically designed to be transported by helicopter.