The Rolls-Royce Crecy was a British experimental two-stroke, 90-degree, V12, liquid-cooled aero-engine of 1,593.4 cu.in (26.11 L) capacity, featuring sleeve valves and direct petrol injection. Initially intended for a high-speed "sprint" interceptor fighter, the Crecy was later seen as an economical high-altitude long-range powerplant. Developed between 1941 and 1946, it was among the most advanced two-stroke aero-engines ever built. The engine never reached flight trials and the project was cancelled in December 1945, overtaken by the progress of jet engine development.
The engine was named after the Battle of Crécy, after Rolls-Royce chose battles as the theme for naming their two-stroke aero engines. Rolls-Royce did not develop any other engines of this type.
Design and development
Origins
Sir Henry Tizard, Chairman of the Aeronautical Research Committee (ARC), was a proponent of a high-powered "sprint" engine for fighter aircraft and had foreseen the need for such a powerplant as early as 1935 with the threat of German air power looming. It has been suggested that Tizard influenced his personal friend Harry Ricardo to develop what eventually became the Crecy. The idea was officially discussed for the first time at an engine sub-committee meeting in December 1935.
Previous experience gained between 1927 and 1930 using two converted Rolls-Royce Kestrel engines through an Air Ministry contract had proven the worth of further research into a two-stroke sleeve-valved design. Both these engines had initially been converted to diesel sleeve-valved operation with a lower power output than the original design being noted along with increased mechanical failures, although one converted Kestrel was subsequently used successfully by Captain George Eyston in a land-speed record car named Speed of the Wind. The second engine was further converted to petrol injection which then gave a marked power increase over the standard Kestrel.
Single-cylinder development began in 1937 under project engineer Harry Wood using a test unit designed by Ricardo. The Crecy was originally conceived as a compression ignition engine and Rolls-Royce had previously converted a Kestrel engine to run on Diesel. By the time they started development of the Crecy itself, in conjunction with the Ricardo company, the decision had been taken by the Air Ministry to revert to a more conventional spark-ignition layout, although still retaining fuel injection.
Technical description
The Crecy has been described as one of the most advanced two-stroke aero engines ever built.
The first complete V12 engine was built in 1941, designed by a team led by Harry Wood with Eddie Gass as the Chief Designer. Bore was 5.1 in (129.5 mm), stroke 6.5 in (165.1 mm), compression ratio 7:1 and weight 1,900 lb (862 kg). The firing angle was 30 degrees BTDC, and 15 lbf/in² (100 kPa) supercharger boost was typical. In bench-testing it produced , but there were problems with vibration and the cooling of the pistons and sleeves. The thrust produced by the exceptionally loud two-stroke exhaust was estimated as being equivalent to a 30% increase in power at the propeller on top of the rated output of the engine. The power of the engine was interesting in its own right, but the additional exhaust thrust at high speed could have made it a useful stop gap between engines such as the Rolls-Royce Merlin and anticipated jet engines. Serial numbers were even, because Rolls-Royce practice was to have even numbers for engines rotating clockwise when viewed from the front.
Sleeve valves
The reciprocating sleeve valves were open-ended, rather than sealing in a junk head. The open end uncovered the exhaust ports high in the cylinder wall at the bottom of the sleeves' stroke, leaving the ports cut into the sleeve to handle the incoming charge only. The sleeves had a stroke of 30% of the piston travel at 1.950 in (49.5 mm) and operated 15 degrees in advance of the crankshaft. The Crecy sleeve valves were of similar construction but differed in their operation compared to the rotary sleeve valve design that was pioneered by Roy Fedden, and used successfully for the first time in an aircraft engine, the Bristol Perseus, in 1932.