Wire wheels, wire-spoked wheels, tension-spoked wheels, or "suspension" wheels are wheels whose rims connect to their hubs by wire spokes. Although these wires are considerably stiffer than a similar diameter wire rope, they function mechanically the same as tensioned flexible wires, keeping the rim true while supporting applied loads. The term suspension wheel should not be confused with vehicle suspension.

Wire wheels are used on most bicycles and are still used on many motorcycles. They were invented by aeronautical engineer George Cayley in 1808. Although Cayley first proposed wire wheels, he did not apply for a patent. The first patent for wire wheels was issued to Theodore Jones of London, England on October 11, 1826. Eugène Meyer of Paris, France was the first person to receive, in 1869, a patent for wire wheels on bicycles.

Wire wheel

Bicycle wheels were not strong enough for cars until the development of tangentially spoked wheels. They rapidly became well established in the bicycle and motor tricycle world but were not common on cars until around 1907. This was encouraged by the Rudge-Whitworth patented detachable and interchangeable wheels designed by John Pugh. These wheels owed their resistance to braking and accelerative stresses to their two inner rows of tangential spokes. An outer row of radial spokes gave lateral strength against cornering stresses. These wheels were deeply dished so that steering pivot pins might lie as near as possible to the center-line of the tires. Their second feature was that they were easily detachable being mounted on splined false hubs. A process of assembling wire wheels is described as wheelbuilding.

Wire wheel

On automobiles

From the earliest days automobiles used either wire wheels or heavy wooden or pressed steel spoked artillery type. The development of the quick detachable hubs of either Rudge-Whitworth or Riley design did much to popularise wire wheels and incidentally led to the fitting of "spare wheels". After their wooden spoked artillery wheels proved inadequate many US manufacturers paid John Pugh of Rudge-Whitworth royalties to manufacture wire wheels using his patents. Artillery wheels fell out of favour in the late 1920s and the development of the cheaper pressed steel wheels by Joseph Sankey replaced wire wheels wherever the premium price of wire wheels was not justified by their weight saving.

Wire wheel

Sports cars

Before 1960, sports/racing cars usually had Rudge-Whitworth centerlock wire wheels equipped with splined hubs and a quick-release "knockoff" (central wing nut) locking cap that could be unscrewed by striking a wing of the nut with a special alloy mallet or "knockoff hammer". Some jurisdictions, including the United States and West Germany, prohibited eared hubcaps for safety reasons in the late 1960s. In response, some manufacturers (e.g. Maserati) preferred to hold the wheel on the splined hub by capping with a single conventional unwinged hex nut requiring a special large spanner.

In the 1960s, even lighter cast alloy wheels became usual—at first with splined hubs and knock-off caps—and now predominate. New versions of wire wheels are still made but often with standard hub bolt patterns covered by a center cap to fit without adapters.

On motorcycles

At one time, motorcycles used wire wheels built up from separate components, but, except for adventure, enduro or dirtbikes, they are now mainly used for their retro appearance.

On bicycles

The first commercially successful use of wired wheels was on bicycles. They were introduced early on in the development of the bicycle, following soon after the adoption of solid rubber tires. This development marked a major improvement over the older wooden wheels, both in terms of weight and comfort (the increased elasticity of the wheel helping to absorb road vibrations).

In England, the engineer William Stanley developed the steel-wired spider wheel in 1849, an improvement over the cumbersome wooden spoked wheels then fitted to the tricycles that his employer was making.

Bicycle manufacturers build millions of wheels annually, using the common crossed-spoke patterns whose crossings of adjacent spokes are governed by the number of spokes in the wheel. Wheelbuilders of racing teams and in good bicycle shops build wheels to other patterns such as two-cross, one-cross, or no-cross (usually called radial). Many of these patterns have been used for more than 100 years. It is claimed that crossed patterns have more strength and stability, and that irregular patterns are art forms and have little structural merit.