For the flanks of the teeth setting numbers are obtained from a separate table, and the instrument is turned upside down, and the tangent line D F, Fig. 137, is drawn from the side of the tooth (instead of from the centre), as shown in Fig. 138.

It is obvious that this odontograph may be set upon a radial arm and used as a template, as shown in Fig. 126, in which case the instrument would require but four settings for the whole wheel, while rolling segments and the making of templates are entirely dispensed with, and the degree of accuracy is greater than is obtainable by means of the employment of arcs of circles.

Modern Machine-Shop Practice, Vol. I (of 2) — Part 96

The tables wherefrom to find the number or mark on the graduated edge, which is to be placed coincident with the tangent line in each case, are as follows:--

Modern Machine-Shop Practice, Vol. I (of 2) — Part 96

TABLE OF TABULAR VALUES WHICH, MULTIPLIED BY THE ARC PITCH OF THE TEETH, GIVES THE SETTING NUMBER ON THE GRADUATED EDGE OF THE INSTRUMENT.

Modern Machine-Shop Practice, Vol. I (of 2) — Part 96

+--------------------+-----------------------------------------------------+ | | Number of Teeth in Wheel Sought; or, Wheel for | | | Which Teeth are Sought. | | +-----+-----+-----+-----+-----+-----+-----+-----+-----+ | | 8 | 12 | 16 | 20 | 30 | 40 | 50 | 60 | 70 | | +-----+-----+-----+-----+-----+-----+-----+-----+-----+ | | _For Faces: Flanks Radial or Curved._ | | RATIOS.[7] | Draw Setting Tangent at Middle of Tooth.-- | | | Epicycloidal Spur or Bevel Gearing. | +--------------------+-----+-----+-----+-----+-----+-----+-----+-----+-----+ | 1/12 = .083 | .32 | .39 | .46 | .51 | | | | | | | 1/4 = .250 | .31 | .37 | .44 | .49 | .61 | .70 | .78 | .85 | .92 | | 1/2 = .500 | .28 | .34 | .41 | .46 | .57 | .66 | .73 | .80 | .87 | | 2/3 = .667 | .27 | .32 | .38 | .43 | .54 | .62 | .70 | .77 | .83 | | 1 | .23 | .28 | .34 | .39 | .49 | .58 | .65 | .72 | .78 | | 3/2 = 1.50 | .19 | .25 | .29 | .34 | .44 | .51 | .58 | .64 | .69 | | 2 | .17 | .22 | .26 | .30 | .38 | .46 | .53 | .59 | .63 | | 3 | | .16 | .19 | .23 | .31 | .38 | .44 | .49 | .53 | | 4 | | .14 | .17 | .20 | .26 | .33 | .38 | .42 | .46 | | 6 | | | | | .22 | .26 | .30 | .34 | .37 | | 12 | | | | | | .20 | .23 | .25 | .28 | | 24 | | | | | | | | | | +--------------------+-----+-----+-----+-----+-----+-----+-----+-----+-----+ | | Number of Teeth in Wheel Sought; or, Wheel for| | | Which Teeth are Sought. | | +-----+-----+-----+-----+-----+-----+-----+-----+ | | 80 | 90 | 100 | 120 | 150 | 200 | 300 | 500 | | +-----+-----+-----+-----+-----+-----+-----+-----+ | | _For Faces: Flanks Radial or Curved._ | | RATIOS.[7] | Draw Setting Tangent at Middle of Tooth.-- | | | Epicycloidal Spur or Bevel Gearing. | +--------------------+-----+-----+-----+-----+-----+-----+-----+-----+ | 1/12 = .083 | | | | | | | | | | 1/4 = .250 | .99 | 1.05| 1.11| 1.22| 1.36| 1.55| 1.94| 2.54| | 1/2 = .500 | .93 | 1.00| 1.06| 1.15| 1.29| 1.50| 1.86| 2.41| | 2/3 = .667 | .89 | .95| 1.01| 1.11| 1.24| 1.45| 1.79| 2.32| | 1 | .83 | .89| .94| 1.03| 1.15| 1.36| 1.65| 2.10| | 3/2 = 1.50 | .74 | .79| .84| .93| 1.05| 1.25| 1.53| 1.94| | 2 | .68 | .72| .76| .84| .95| 1.13| 1.40| 1.81| | 3 | .57 | .60| .63| .71| .82| .97| 1.23| 1.60| | 4 | .49 | .53| .56| .63| .73| .87| 1.08| 1.42| | 6 | .41 | .44| .47| .53| .61| .71| .90| 1.20| | 12 | .30 | .32| .34| .37| .42| .49| .60| .82| | 24 | | .19| .21| .23| .26| .31| .40| .57| +--------------------+-----+-----+-----+-----+-----+-----+-----+-----+ +--------------------+-----------------------------------------------------+ | | Number of Teeth in Wheel Sought; or, Wheel for | | | Which Teeth are Sought. | | +-----+-----+-----+-----+-----+-----+-----+-----+-----+ | | 8 | 12 | 16 | 20 | 30 | 40 | 50 | 60 | 70 | | +-----+-----+-----+-----+-----+-----+-----+-----+-----+ | | _For Flanks, when Curved._ | | | Draw Setting Tangent at Side of Tooth.-- | | | Epicycloidal Spur and Bevel Gearing. | |D C | Faces of Internal, and Flanks of Pinion Teeth. | |e u +-----+-----+-----+-----+-----+-----+-----+-----+-----+ |g F r { 1.5 slight.| .77 | .98 | 1.18| 1.36| 1.75| 2.05| 2.31| 2.56| 2.75| |r l v { 2 good. | .44 | .54 | .63| .72 | .92| 1.09| 1.24| 1.38| 1.49| |e a a { 3 more. | .20 | .28 | .35| .40 | .54| .65| .76| .86| .95| |e n t { 4 much. | | .20 | .23| .25 | .34| .42| .51| .59| .66| | k u { 6 | | | .16| .17 | .26| .32| .38| .43| .48| |o r { 12 | | | | | .19| .24| .28| .31| .34| |f e { 24 | | | | | | | | | | +--------------------+-----+-----+-----+-----+-----+-----+-----+-----+-----+ | | Number of Teeth in Wheel Sought; or, Wheel for| | | Which Teeth are Sought. | | +-----+-----+-----+-----+-----+-----+-----+-----+ | | 80 | 90 | 100 | 120 | 150 | 200 | 300 | 500 | | +-----+-----+-----+-----+-----+-----+-----+-----+ | | _For Flanks, when Curved._ | | | Draw Setting Tangent at Side of Tooth.-- | | | Epicycloidal Spur and Bevel Gearing.