135 film, more popularly referred to as 35 mm film or 35 mm, is a format of photographic film used for still photography. It is a film with a film gauge of loaded into a standardized type of magazine – also referred to as a cassette or cartridge – for use in 135 film cameras. The engineering standard for this film is controlled by ISO 1007 titled '135-size film and magazine'.
The term 135 was introduced by Kodak in 1934 as a designation for 35 mm film specifically for still photography, perforated with Kodak Standard perforations. It quickly grew in popularity, surpassing 120 film by the late 1960s to become the most popular photographic film size. Despite competition from formats such as 828, 126, 110, and APS, it remains the most popular film size today.
The size of the 135 film frame with its aspect ratio of 1:1.50 has been adopted by many high-end digital single-lens reflex and digital mirrorless cameras, commonly referred to as "full frame". Even though the format is much smaller than historical medium format and large format film, being historically referred to as miniature format or small format, it is much larger than image sensors in most compact cameras and smart phone cameras.
Characteristics
Cassette
Individual rolls of 135 film are enclosed in single-spool, light-tight, metal cassettes to allow cameras to be loaded in daylight. The film is clipped or taped to a spool and exits via a slot lined with flocking. The end of the film is cut on one side to form a leader. It has the same dimensions and perforation pitch as 35 mm movie print film (also called "long pitch", KS-1870, whereas 35 mm professional motion picture camera films are always "short pitch", BH-1866).
Most cameras require the film to be rewound before the camera is opened. Some motorized cameras unwind the film fully upon loading and then expose the images in reverse order, returning the film to the cassette; this protects all images except the last one or two, should the camera back be accidentally opened. Disposable cameras use the same technique so that the user does not have to rewind.
Since the 1980s, film cassettes have been marked with a DX encoding six-digit barcode pattern, which identifies the manufacturer and film type (and thus processing method), and the number of exposures, for the use of photofinishing laboratories. The cassettes are also manufactured with a Camera Auto Sensing code constructed as two rows of six rectangular areas on the metal cassette surface which are either conductive or insulating, representing 32 possible film speeds, eight possible film lengths, and four possible values of exposure tolerance or latitude. Conforming cameras detect at least some of these areas; only three contacts are needed to set a light meter for the four most popular film speeds.
Film type and speed
The 135 film has been made in several emulsion types and sensitivities (film speeds) described by ISO standards. Since the introduction of digital cameras the most usual films have colour emulsions of ISO 100/21° to ISO 800/30°. Films of lower sensitivity (and better picture quality) and higher sensitivity (for low light) are for more specialist purposes. There are colour and monochrome films, negative and positive. Monochrome film is usually panchromatic; orthochromatic has fallen out of use. Film designed to be sensitive to infrared radiation can be obtained, both monochrome and with false-colour (or pseudocolour) rendition. More exotic emulsions have been available in 135 than other roll-film sizes.
Image format
The term 135 format usually refers to a 24×36 mm film format, commonly known as 35 mm format. The 24×36 mm format is common to digital image sensors, where it is typically referred to as full frame format.
On 135 film, the typical cameras produce a frame where the longer dimension of the 24×36 mm frame runs parallel to the length of the film. The perforation size and pitch are according to the standard specification KS-1870. For each frame, the film advances 8 perforations. This is specified as 38.00 mm. This allows for 2 mm gaps between frames. Camera models typically have different locations for the sprocket which advances the film. Therefore, each camera model's frame may vary in position relative to the perforations. The film is approximately 0.14 mm thick.