The Daewoo Espero (also known as Daewoo Aranos in Spain) is a four-door, five-seater mid-sized saloon produced by the South Korean company Daewoo Motors from September 1990 to 1997. The Espero was the first car entirely developed by Daewoo, which until then had only manufactured models developed by Opel. With the body designed by Bertone, the model is based on the platform of the Daewoo LeMans, a badge engineered version of the Opel Kadett manufactured in South Korea. The engines were supplied by Holden, with options ranging from the GM Family 1 1.5L to the GM Family II 2.0L. The Espero was replaced by the Daewoo Nubira in 1997, but continued to be produced until 1999 in Eastern Europe.

Development

In the mid-1980s, Daewoo Motors was looking to enter in the mid-sized saloon market, which already had competitors like the Hyundai Sonata. To that end, it began developing a new model in 1986, codenamed "J-Car" (not to be confused with General Motors' J-Car, the company's worldwide car project from the 1980s). It then acquired from Bertone a body design previously discarded by Citroën, which would be used in the future successor of the Citroën BX. With access to General Motors technologies limited by contractual terms, Daewoo made extensive use of parts already being used on the Daewoo LeMans production. The steering, suspension, brakes and powertrain systems were the same as those used on the LeMans. The platform was also derived from the LeMans, but elongated behind the B-pillar to give the Espero longer wheelbase than the LeMans.

Daewoo Espero

The Espero debuted on the Korean market in August 1990. The Espero achieved very good results in the wind tunnel, at 0.29 Cd.

Daewoo Espero

Prototype

There was also a prototype that looked very similar to the Espero. This prototype is called DEV 2 (DEV meaning Daewoo Electric Vehicle) and was presented in 1995 at the Korea Motor Show in Seoul together with the Daewoo Bucrane concept, Tico concept, Nexia, Arcadia and the NGV3 concept. It was basically a version of the Espero but made out of recyclable materials which did not impact the environment. The DEV 2 had a redesigned front. This prototype was shown only in South Korea and only once at these fairs. It was painted white pearl and had 'DEV' badges in blue at the rear doors, its interior was white and the rims where a three spoke design and white as well.

Daewoo Espero

Under the hood it was powered by an electric motor which was a water-cooled AC induction motor (86 kW) with performance figures with 0–100 km (0-60 mph) acceleration of 13 seconds. Top speed was around 85 mph. 22 new lead acid batteries were laid on the floor of the body, and one charge distance of 80 km (49.7 miles) was carried out.

It was said that the perfection was high but the performance and the range as an electric car was low.

Other Dimensions

The Asian Market

Korea

In Korea, the Espero made its debut in August 1990. The styling was very different from the European Espero's, including no badge at the front but at the rear and on the steering wheel; the badge was black and had white three waves and white writing 'ESPERO' underneath it. The first version had different rear lights which the brake and indicator lights extended to the boot lid (though there were no illuminating lights at the boot lid) and differently styled hubcaps.

In the pre-facelift, the range consisted of two models, named '1.5 DOHC' (being the base model) which had standard hubcaps and then the '2.0 SOHC' which had different styled hubcaps. The '2.0 SOHC' also had a version with package, being the top of the range model.

In the cabin of the Korean Espero, a different steering wheel and an electronic dash was available with orange letters and accents. The steering wheel was slightly different from the three-spoke wheels in Europe, and more like the steering wheel from an Opel Vectra A/Vauxhall Cavalier MK3 except that the badge was different (again, the black emblem). No airbag was available. The front door cards were different: rather than the wrap-around design in European models, the vents were more square like and the grab handle was more ergonomic rather than just a pocket design. The centre console was flat and more angular.

In late 1991, a facelift of the Espero was made. This included redesigned hubcaps (base model), a black badge saying 'ESPERO' at the rear, the rear lights were redesigned and now the black badge was put at the front. The boot opening was redesigned with a swivel badge over the keyhole to open the boot. This also meant the trim levels were revised, the base model being the 1.5 MPFi and the 2.0 MPFi (or with the package).