Mineral trioxide aggregate (MTA) was developed for use as a dental root repair material by Mahmoud Torabinejad. It is formulated from commercial Portland cement, combined with bismuth oxide powder for radio-opacity. MTA is used for creating apical plugs during apexification, repairing root perforations during root canal therapy, and treating internal root resorption. This can be used for root-end filling material and as pulp capping material. Originally, MTA was dark gray in color, but white versions have been on the market since 2002.

Portland cement is a term applied to a class of materials covering a range of compositions (between silica alumina and calcia). The composition, fineness, setting time and strength of Portland cement are not controlled or guaranteed. Portland cement is an unsuitable substitute for MTA based on several characteristics that are essential to the performance: freedom from heavy metals, dimensional stability and fineness. The FDA requires dental materials to have high purity and be lead and arsenic-free, unlike commercial Portland cement.

Mineral trioxide aggregate

Composition

MTA is composed of tricalcium silicate, dicalcium silicate, tricalcium aluminate, tetracalcium aluminoferrite, calcium sulfate, and bismuth oxide. The later 4 phases vary among the commercial products available.

Mineral trioxide aggregate

Newly developed fast-set MTAs were developed by Pozzolan Cement or Zeolite Cement. These were used by pozzolanic reaction. Pozzolan Cement is a mineral aggregate with watery calcium silicate hydration.

Mineral trioxide aggregate

Characteristics and products

Biocompatible with periradicular tissues

Non cytotoxic, but antimicrobial to bacteria

Non-resorbable

Minimal leakage around the margins. Very basic AKA alkaline (high pH when mixed with water). As a root-end filling material MTA shows less leakage than other root-end filling materials, which means bacterial migration to the apex is diminished. Treated area needs to be infection free when applying MTA, because an acidic environment will prevent MTA from setting. Compressive strength develops over a period of 28 days, similar to Portland cement. Strengths of more than 50 MPa are achieved when mixed in a powder-to-liquid ratio of more than 3 to 1.

Originally, MTA products required a few hours for the initial and final setting, which is uncommon in dental materials. Newer materials are available that set more quickly.

MTA Plus is washout resistant.

MTA Products: Gray: Calcium Alumino-Silicate Cement (C3S, C2S with C3A)- Portland Cement Type I with Bismuth Trioxide. (ex. ProRoot MTA, MTA Angelus) White : Calcium Carbonate alumino-silicate Cement (CaCO3 + SiO2 with Al2O3). Final phase is medical grade material similar to Portland Cement. (Limestone Portland Cement) (ex. ProRoot MTA White, MTA Angelus Blanc, EndoCem/Zr, MM MTA, Tech BioSeal MTA, Trioxident, most white MTAs). Bioceramic (ex. OrthoMTA, RetroMTA, Angelus MTA-Fillapex)

GIC solution is polyacrylic acid. GIC is alumino-silicate (glass) bioceramic cement. As MTA is mainly composed of calcium-alumino-silicate, PAA (polyacrylic acid) is an accelerant for MTA. PAA set MTA within 15–18 minutes. More aluminate, faster set. Also high concentrated calcium chloride (CaCl2, 70% more) is well known as accelerator of Portland cement. So high concentrated -over 70%- Calcium Chloride solution sets MTA within 12 minutes. Or Pozzolanic reaction is also faster set chemical reaction of calcium silicate hydrate. But pozzolanic reacted cement has lower compressive strength at 15 MPa maximum. Easy broken and easily removable property of pozzolanic MTA.

Usage in some clinical cases

Root-end filling after apicectomy

In root canal therapy where an apical infection is persistent, an apicectomy may be required. Flap is raised over the tooth and the root tip is resected and a cavity created (3–4 mm) in the root tip remaining. Retrograde application of MTA to the root tip cavity is completed.