The P-47 Thunderbolt was a World War II fighter aircraft built by Republic Aviation from 1941 to 1945.

Early designs

XP-47 (AP-10)

Republic P-47 Thunderbolt variants

In response to a USAAC requirement for a new fighter aircraft, Republic Aviation engineer Alexander Kartveli proposed the AP-10 lightweight high-altitude interceptor on August 1, 1939. As originally proposed, the AP-10 was to have been powered by a 1,150 hp Allison V-1710-39 12-cylinder inline engine and have an armament consisting of two nose-mounted .50 in (12.7 mm) M2 Browning machine guns. Maximum speed was estimated to be 415 mph, while gross weight was to be 4,900 lb.

Republic P-47 Thunderbolt variants

The USAAC was impressed by the AP-10 proposal, but expressed concerns that it would be underarmed. Kartveli revised the AP-10 by slightly increasing its size and mounting two .30 in (7.62 mm) M1919 Browning machine guns in each wing, raising the gross weight to 6,570 lb. Satisfied, the USAAC ordered a single prototype under the designation XP-47, in November 1939.

Republic P-47 Thunderbolt variants

XP-47A

In addition to the XP-47, the USAAC also ordered another prototype as the XP-47A. This prototype was ordered without military equipment, allowing for it to be finished and tested before the XP-47.

In early 1940, combat reports from war in Europe indicated that the P-47 was inferior to Luftwaffe fighters. In response, the USAAC issued new requirements for a fighter including an airspeed of 400 mph at 25,000 ft, an armament of six or (preferably) eight .50 in machine guns, cockpit armor plating, self-sealing fuel tanks, and a minimum fuel load of 315 gallons. Expecting the USAAC to reject the XP-47 for the more suitable Curtiss XP-46, Republic canceled the XP-47 and XP-47A and Kartveli began an extensive redesign of the aircraft.

Razorback Thunderbolts

P-47B

On June 12, 1940, Kartveli submitted the redesigned AP-10 to the USAAC. The new aircraft was much larger than the original, and the inline engine was swapped for a turbo-supercharged Pratt & Whitney R-2800 Double Wasp 18-cylinder radial engine. Armament was increased to eight M2 Brownings, four mounted in each wing, making it one of the heaviest-armed fighters considered by the USAAC at the time. The expected performance met USAAC requirements, however, its fuel load fell slightly short. Despite this, the USAAC ordered a prototype of the improved design as the XP-47B, on September 6, 1940.

The XP-47B was first flown on May 6, 1941. It was powered by a 1,960 hp XR-2800-21 engine and featured an elliptical wing, an all-metal construction (except for the fabric-covered control surfaces), and a hinged canopy. The main landing gear retracted inward into the wings, telescoping nine inches to clear the underside of the fuselage, and the steerable tailwheel was fully retractable. With a loaded weight of 12,086 lb, the XP-47B was almost twice as heavy as its competitors. Performance was higher than expected with a maximum speed of 412 mph.

The XP-47B crashed on August 8, 1942, however, an order for 773 production aircraft had been placed almost two years before on September 13, 1940. The production aircraft, designated P-47B, differed from the prototype in that they were powered by a 2,000 hp production R-2800-21 engine, a sliding canopy in place of the original hinged unit, and redesigned metal ailerons and elevators. Only 171 of the original order were completed as P-47Bs before production switched to the P-47C. The aircraft's nickname, Thunderbolt, was created by Republic's Director of Military Contracts, C. Hart Miller.

Sub-variants and modifications

XP-47B, single prototype powered by a 1,960 hp XR-2800-21 engine. P-47B-RE, 171 aircraft powered by a 2,000 hp R-2800-21 engine with other modifications. RP-47B, designation originally applied to a handful of P-47B modified into photo-reconnaissance aircraft with a camera mounted in the port intercooler vent. Later applied to all P-47Bs in 1944 to denote its status as restricted from combat.

XP-47E

The final P-47B was converted in September 1942 into a prototype for a high-altitude variant as the XP-47E. Modifications included a pressurized cockpit with a hinged canopy. The project was canceled due to increased emphasis on low-level operations over Europe.

XP-47F

Another P-47B was fitted with a larger-area laminar-flow wing as the XP-47F. The XP-47F was first flown on September 17, 1942, but project was ultimately canceled when the aircraft crashed and no production aircraft followed.