The M103 Heavy Tank (officially designated 120mm Gun Combat Tank M103, initially T43) was a heavy tank that served in the United States Army and the United States Marine Corps during the Cold War. Introduced in 1957, it served through 1974, by which time evolution of the concept of a main battle tank considered heavy tanks obsolete.
Design and development
In December 1950 the U.S. Army made blueprints for a heavy tank reference design. In January 1951 it awarded Chrysler a $99 million contract to produce the tank. Chrysler tasked Robert T. Keller, the son of Chrysler Board Chairman K.T. Keller, with overseeing its design, and construction at the company's new Newark, Delaware, tank plant.
The first T43 pilot model was completed in November 1951. Officials said the tank would "out-slug any land-fighting machine ever built."
Like the contemporary British Conqueror, the M103 was designed to counter Soviet heavy tanks, such as the later IS-series tanks or the T-10 if conflict with the Eastern Bloc broke out. Its long-ranged 120 mm cannon was designed to destroy enemy tanks at extreme distances.
Some 300 tanks were built in 1953–54, initially designated T43E1. Details about the tank, including production plans and specifications, were tightly held. Seeking to keep the tank out of public sight, Secretary of Defense Charles E. Wilson nixed an October 1953 exhibition for the American Ordnance Association at Aberdeen Proving Ground. In May 1954 the tank was debuted publicly at a demonstration at the Newark tank plant.
In 1953 the Pentagon began a reversal of the President Truman administration policy of a broad production base in favor of Wilson's "single, efficient producer" concept. In September Wilson chose General Motors over Chrysler to take over production of the M48 Patton. General Motors would also become heir to any additional T43 orders after Chrysler tank production wrapped up in June 1954.
Testing was unsatisfactory, with the tanks failing to meet Continental Army Command's standards and being put into storage in August 1955. Following the approval of 98 improvements the tank was redesignated the M103 Heavy Tank in April 1956. Of the 300 T43E1s built, 80 went to the US Army (74 of which were rebuilt to M103 standard), and 220 were accepted by the US Marine Corps, to be used as infantry support, rebuilt successively to improved M103A1 then M103A2 standards.
A House Government Operations subcommittee report in July 1957 called for the heavy tank program to be audited. Investigators had been unable to determine the cost of the program, which was estimated in the hundreds of millions of dollars. The report said the Army had hastened production of the tank for war in Korea despite there being no need for it there. The tank was also unsuited to the rigors of the nuclear battlefield, the report said.
Specifics
Following contemporary American design philosophy, the M103 was built with a two-piece, cast elliptic armor scheme, similar to the M48's design. It featured seven road wheels per side, mounted with long-arm independent torsion bars. The track was shoed in steel backed rubber chevron tracks, allowing for a ground pressure of 12.9 psi. The Continental AV-1790 engine was placed at the rear of the tank, and produced a maximum output of and of torque, fed through a General Motors CD-850-4 two-speed transmission. This allowed the 60-ton heavy tank to achieve a maximum road speed of and a maximum climbing gradient of 60%.
Initial production versions suffered a host of drivetrain mechanical problems. The Continental powerpack, shared by the much lighter M48/M60 tanks, was insufficient to drive the much heavier M103. The resulting performance of the tank was dismal; being severely underpowered and very fuel intensive. This presented a host of logistical problems for the vehicle, most prominently the extremely limited range of just . Though this was partially corrected with the introduction of the AV-1790-2 diesel unit, it would remain cumbersome and fuel-thirsty for the majority of its service life.
For ease of production, many of the large components of the tank were made from cast armor. This design scheme was also much more mass efficient than traditional rolled plate armor. Despite being better protected than the T29-series of prototypes which preceded it, the M103 was nearly 10 tons lighter, making it competitive with the Soviet T-10/IS-8 tank. The frontal hull glacis was a compound pike, welded at the center seam, with up to 10 inches thick armor at the front. The turret was a massive single-piece cast design, fitted with heavily sloped 10-inch (254 mm) rolled-homogeneous armor.