Advanced Telecommunications Computing Architecture (ATCA or AdvancedTCA) is the largest specification effort in the history of the PCI Industrial Computer Manufacturers Group (PICMG), with more than 100 companies participating. Known as AdvancedTCA, the official specification designation PICMG 3.x (see below) was ratified by the PICMG organization in December 2002. AdvancedTCA is targeted primarily to requirements for "carrier grade" communications equipment, but has recently expanded its reach into more ruggedized applications geared toward the military/aerospace industries as well. This series of specifications incorporates the latest trends in high speed interconnect technologies, next-generation processors, and improved Reliability, Availability and Serviceability (RAS).

Mechanical specifications

An AdvancedTCA board (blade) is 280 mm deep and 322 mm high. The boards have a metal front panel and a metal cover on the bottom of the printed circuit board to limit electromagnetic interference and to limit the spread of fire. The locking injector-ejector handle (lever) actuates a microswitch to let the Intelligent Platform Management Controller (IPMC) know that an operator wants to remove a board, or that the board has just been installed, thus activating the hot-swap procedure. AdvancedTCA boards support the use of PCI Mezzanine Card (PMC) or Advanced Mezzanine Card (AMC) expansion mezzanines.

Advanced Telecommunications Computing Architecture

The shelf supports RTMs (Rear Transition Modules). RTMs plug into the back of the shelf in slot locations that match the front boards. The RTM and the front board are interconnected through a Zone-3 connector. The Zone-3 connector is not defined by the AdvancedTCA specification.

Advanced Telecommunications Computing Architecture

Each shelf slot is 30.48 mm wide. This allows for 14-board chassis to be installed in a 19-inch rack-mountable system and 16 boards in an ETSI rack-mountable system. A typical 14-slot system is 12 or 13 rack units high. The large AdvancedTCA shelves are targeted to the telecommunication market so the airflow goes in the front of the shelf, across the boards from bottom to top, and out the rear of the shelf. Smaller shelves that are used in enterprise applications typically have horizontal air flow.

Advanced Telecommunications Computing Architecture

The small-medium AdvancedTCA shelves are targeted to the telecommunication market; for the lab research operation, some shelves have an open cover in order to make testing easier.

Backplane architecture

The AdvancedTCA backplane provides point-to-point connections between the boards and does not use a data bus. The backplane definition is divided into three sections; Zone-1, Zone-2, and Zone-3. The connectors in Zone-1 provide redundant −48 VDC power and Shelf Management signals to the boards. The connectors in Zone-2 provide the connections to the Base Interface and Fabric Interface. All Fabric connections use point-to-point 100 Ω differential signals. Zone-2 is called "Fabric Agnostic" which means that any Fabric that can use 100 Ω differential signals can be used with an AdvancedTCA backplane.

The connectors in Zone-3 are user defined and are usually used to connect a front board to a Rear Transition Module. The Zone-3 area can also hold a special backplane to interconnect boards with signals that are not defined in the AdvancedTCA specification.

The AdvancedTCA Fabric specification uses Logical Slots to describe the interconnections. The Fabric Switch Boards go in Logical Slots 1 and 2. The chassis manufacturer is free to decide the relationship between Logical and Physical Slots in a chassis. The chassis Field Replaceable Units (FRU) data includes an Address Table that describes the relationship between the Logical and Physical slots.

The Shelf Managers communicate with each board and FRU in the chassis with IPMI (Intelligent Platform Management Interface) protocols running on redundant I²C buses on the Zone-1 connectors.

The Base Interface is the primary Fabric on the Zone-2 connectors and allocates 4 differential pairs per Base Channel. It is wired as a Dual-Star with redundant fabric hub slots at the core. It is commonly used for out of band management, firmware uploading, OS boot, etc.

The Fabric Interface on the backplane supports many different Fabrics and can be wired as a Dual-Star, Dual-Dual-Star, Mesh, Replicated-Mesh or other architectures. It allocates 8 differential pairs per Fabric Channel and each Channel can be divided into four 2-pair Ports. The Fabric Interface is typically used to move data between the boards and the outside network.

The Synchronization Clock Interface routes MLVDS (Multipoint Low-voltage differential signaling) clock signals over multiple 130 Ω buses. The clocks are typically used to synchronize telecom interfaces.