The Um interface is the air interface for the GSM mobile telephone standard. It is the interface between the mobile station (MS) and the Base transceiver station (BTS). It is called Um because it is the mobile analog to the U interface of ISDN. Um is defined in the GSM 04.xx and 05.xx series of specifications. Um can also support GPRS packet-oriented communication.
Um layers
The layers of GSM are initially defined in GSM 04.01 Section 7 and roughly follow the OSI model. Um is defined in the lower three layers of the model.
Physical Layer (L1) The Um physical layer is defined in the GSM 05.xx series of specifications, with the introduction and overview in GSM 05.01. For most channels, Um L1 transmits and receives 184-bit control frames or 260-bit vocoder frames over the radio interface in 148-bit bursts with one burst per timeslot. There are three sublayers: Radiomodem. This is the actual radio transceiver, defined largely in GSM 05.04 and 05.05. Multiplexing and Timing. GSM uses TDMA to subdivide each radio channel into as many as 16 traffic channels or as many as 64 control channels. The multiplexing patterns are defined in GSM 05.02. Coding. This sublayer is defined in GSM 05.03. Um on the physical channel has 26 TDMA frames each frame consisting of 114 info bits each. The length of 26 TDMA frame also called Multi-frame is 120 ms apart.
Radio modem
GSM uses GMSK or 8PSK modulation with 1 bit per symbol which produces a 13/48 MHz (270.833 kHz or 270.833 K symbols/second) symbol rate and a channel spacing of 200 kHz. Since adjacent channels overlap, the standard does not allow adjacent channels to be used in the same cell. The standard defines several bands ranging from 400 MHz to 1990 MHz. Uplink and downlink bands are generally separated by 45 or 50 MHz (at the low-frequency end of the GSM spectrum) and 85 or 90 MHz (at the high-frequency end of the GSM spectrum). Uplink/downlink channel pairs are identified by an index called the ARFCN. Within the BTS, these ARFCNs are given arbitrary carrier indexes C0..Cn-1, with C0 designated as a Beacon Channel and always operated at constant power.
GSM has physical and logical channels. The logical channel is time-multiplexed into 8 timeslots, with each timeslot lasting for 0.577ms and having 156.25 symbol periods. These 8 timeslots form a frame of 1,250 symbol periods. Channels are defined by the number and position of their corresponding burst period. The capacity associated with a single timeslot on a single ARFCN is called a physical channel (PCH) and referred to as "CnTm" where n is a carrier index and m is a timeslot index (0-7).
Each timeslot is occupied by a radio burst with a guard interval, two payload fields, tail bits, and a midamble (or training sequence). The lengths of these fields vary with the burst type but the total burst length is 156.25 symbol periods. The most commonly used burst is the Normal Burst (NB). The fields of the NB are:
Midamble A 26-bits training sequence that helps in multipath equalisation at the center of the burst "Stealing bits" each side of the midamble, used to distinguish control and traffic payloads Payload two 57-bit fields, symmetric about the burst Tail bits 3-bit field, at each end of the burst Guard period 8.25-symbols at the end of the burst
There are several other burst formats, though. Bursts that require higher processing gain for signal acquisition have longer midambles. The random access burst (RACH) has an extended guard period to allow it to be transmitted with incomplete timing acquisition. Burst formats are described in GSM 05.02 Section 5.2.
Multiplexing and timing
Each physical channel is time-multiplexed into multiple logical channels according to the rules of GSM 05.02. One logical channel constitute of 8 burst periods (or physical channels) which is called a Frame. Traffic channel multiplexing follows a 26-frame (0.12 second) cycle called a "multiframe". Control channels follow a 51-frame multiframe cycle. The C0T0 physical channel carries the SCH, which encodes the timing state of the BTS to facilitate synchronization to the TDMA pattern.
GSM timing is driven by the serving BTS through the SCH and FCCH. All clocks in the handset, including the symbol clock and local oscillator, are slaved to signals received from the BTS, as described in GSM 05.10. BTSs in the GSM network can be asynchronous and all timing requirements in the GSM standard can be derived from a stratum-3 OCXO.