(329) The application of this principle is as follows, and it can now be stated that the end of the chain is attached to a nut which slides along the arm, being actuated by the rotation of a screw upon which it fits. Remembering that an acceleration of the terminal velocity and a regulation of the revolution of the spindle is required, the demonstration just given shows that these are obtained by the removal of the nut further from the centre of oscillation. The influence of the pull of the chain upon the barrel when the nut is in the position =K= is much slighter, and shows less variation than when it is at =D=. Every inch which the nut travels outwards has an influence upon this factor, and the conditions of winding are thus accurately regulated. When the winding of the cop begins, the nut is in its lowest position, and the rotation of the barrel is then practically equal. As the nut moves away from the centre the barrel gradually rotates more slowly at the beginning of its inward movement. By the time the most outward position is reached—which, in practice, coincides with the formation of the cop bottom—the variation in the velocity has reached its greatest amount. This, it can be easily seen, is what is wanted. Referring again to Fig. 163, one revolution of the spindle when the yarn is being wound on =A D= would practically take up the same length as would be taken up at the top of the paper tube. But when the faller is guiding the yarn on the conical surface from =E= to =B=, one revolution of the spindle would wind on a greater length at =E= than it would at =B=. Therefore, the initial velocity requires to be less than the terminal. But when the point =E= has become the initial position, the conditions of winding remain thereafter constant, except in so far as is affected by the taper of the blade, and there is no further need for an outward movement of the nut.

(330) The theory underlying the method of winding having thus been dealt with, the mechanism employed can be described. This is shown in Fig. 168, which is a diagram of the whole of the apparatus, and in Fig. 169, which is an enlarged view of a portion of it. The winding arm =M= is centered at its lower end, and has formed on it a toothed quadrant =M^{ 1}=. The “quadrant” =M= oscillates on a short shaft, securely carried by the headstock framing, and receives its forward movement by means of a pinion =Z=, which engages with its teeth. The extent of the quadrant movement is about a quarter circle. The pinion =Z= is mounted on the same centre as a grooved pulley, over which a cord from the back shaft =H= is passed. Thus the rotation of =H= in either direction produces a similar movement in the pinion =Z=; and the effect is, that, while the back shaft is drawing the carriage out, the pinion is revolving so as to raise the arm =M= or cause it to make a backward oscillation. When the back shaft acts as a taking-in shaft, as described in paragraph 315, the pinion =Z= is revolved so as to move the arm =M= forward. The velocity at which the forward stroke is made is by this arrangement a variable one, and completely corresponds to that of the carriage traverse. Inside the winding arm a long slot is formed in which a screw =P= is placed, this being free to revolve. It may be made with a thread of equal pitch throughout, but, as shown, is provided with a thread of varying pitch, which gradually becomes finer towards the outward end of the arm. The reason of this is obvious. The effect of each layer of yarn upon the problem of winding is greater at the beginning of the formation of the cop bottom than when it is more nearly finished. That is, the enlargement of its diameter is relatively greater at the first stage than at any other. For instance, if the diameter is 3/8 inch and it be increased 1/16 inch, the ratio is 1/6th; while if the diameter is 3/4 inch, and the same increase takes place, the ratio is 1/12th only. The variation required in the speed of winding as each layer is wrapped is therefore less in the latter than in the former case. This is the purpose of the helical screw, which gives a quicker advance to the nut in the earlier stages of winding than when the cop bottom is nearly formed.

Modern Cotton Spinning Machinery — Part 151